Loadingbargain728

1. Elm327 Usb software, free download
2. Elm327 Ford Software

Table of Contents

Many Ford, Lincoln, Mercury and Mazda models are equipped with MSCAN bus, in addition to HSCAN bus. ELM327 is supported HSCAN bus, MSCAN bus is not supported by the stock OBD2 ELM327 adapter, because MSCAN bus is a Ford protocol specific solution and on non-OBD2 pins. However, ELM327 is very flexible tool. You need small modification to add the MSCAN bus support.

FVDI SVCI J2534 Programmer is a vehicle communication interface device that full compatible with SAE J2534-1 and partly compatible with SAE J2534-2.It supports most of vehicle communication protocols and can be used as PassThru device for many dealer level diagnostic software.And it can be used as a ELM327 device also,support most of ELM327 software.

SP177-C1 is the best VCMII clone, but it’s too hot and sold out of stock always.Here, obdexpress.co.uk recommend two tool alternatives of VCM II Clone:VCX Nano Ford IDS and ELM327, they can run ForScan and the price is cheaper than VCM2 Clone1. Decent VCX Nano for FordThere’s various clones of fords VCM hardware but the cheapest is the VCX Nano. There are however fake ones out there so try. Ford Ids Software Elm327 Ford IDS (Integrated Diagnostic System) is the current modular diagnostic system to support the latest Ford vehicles. As a Ford Approved device, it is the only diagnostic system supported for use within the Ford Europe dealer and Independent Motor Trade network. FORD/MAZDA SVDI J2534 Diagnostic Tool Supported software for SVCI J2534: Ford IDS V113 Mazda IDS V113 Toyota TIS V13.00.022 Land Rover/Jaguar SDD2 V154.01 ELM327 V2.4.12 ELM327 V2.1 (Notice: only support few part elm327 software, such as scanmaster software) Fly SVDI J2534 VCI Supported software for ELM327: ScanMaster-ELM V2.4.12 PCMSCAN V2.1. Support ELM327 software by one device. Support softwares: J2534 for Ford IDS V111 for Mazda IDS V111 for Toyota TIS V13.00.022 for Land Rover/Jaguar SDD2 V154.01 Support Protocols: ISO9141 IS014230 J1850 VPW J1850 PWM(Ford SCP) IS011898 HS(500K BPS) IS011898 MS(125K BPS) IS015765 HS(500K BPS) IS015765 MS(125K BPS).

How to modify ELM327 with HS/MS CAN switch

The ELM327 OBD2 adapter supported HSCAN bus from stock, because HSCAN bus completely with OBD2 standards. It is support pins 6 and 14. With MSCAN bus occupies pins 3 and 11. The photo below will show the thing (ATTENION: the OBD2 socket on the photo means vehicle one ” OBD2 female”. The adapter is one is “OBD2 male”, so it is “mirrored”.)

The easy methold to implement MSCAN bus support by add a SW that will shift between MSCAN/HSCAN bus. The picure below will show the modification (ATTENION: the OBD2 socket on the picture means one “OBD2 female”. The ELM327 OBD2 adapter is one is “OBD2 male”, so it is “mirror”. The pin are often mixed up because of this. Always remember pins on OBD2 socket. That will help you fast modification)

What are you need modification MSCAN bus?

• You need buy a 6 pin mini-switch of ON-ON type (for example, MTS-202-A2) in any shop that sells electronic components, also prepare a wire.

• Disassemble ELM327 OBD2 adapter(carefully remove the label that hides 4 screws, unscrew them).

• Find a place for the mini-switch (most complex part of the whole operation for some devices that are extremely compact).
• Unsolder wires from pins 6 and 14 of the OBD2 adapter jack and solder them to the 2 middle pins of the mini-switch ON-ON.
• Solder 2 new wires from 2 outer mini-switch pins to pins 6 and 14 of the OBD2 adapter jack.
• Solder 2 other new wires from 2 other outer mini-switch pins to pins 3 and 11 of the OBD2 adapter jack.

• Check the work (it is very important to do not mix CAN-L and CAN-H wires up!) and assembly the ELM327 OBD2 adapter, mark the MSCAN bus and HSCAN bus position on the device box to avoid confusion.

How to use FORScan with EML327 MSCAN

FORScan version no.2 has support of MS CAN bus and optimized for using the HS/MSCAN switch. There is no necessity to adjust any ELM327 OBD2 adapter parameters for MSCAN bus. FORScan makes all the necessary changes in an automated mode. When FORScan establishes a vehicle connection, it analyses the vehicle configuration. Module MS CAN bus are supported, FORScan will ask user about HS/MS CAN switch.

It means FORScan doesn’t expect a presence of MS CAN bus and is not going to look for it. If user confirms the MS/HS switch presence, FORScan will ask user to shift the bus, for example:

Conclusion

Using the HS/MS CAN switch (minimize number of necessary shifts) with FORScan version 2. For example, reading DTCs in all of 5 HS CAN modules and 2 MS CAN modules will always require only 1 shift. Please share it, if this article helps you. If you have BAFX OBD2 adapter, you can modify same as ELM327. Please read modify BAFX adapter or BAFX adapter reviews.

reference from forscan.org

Search rules:

• elm327 mscan
• modify mscan elm327
• modify elm327 ford mazda
• elm327 switch
• mscan hscan
• mscan switch

Description

FVDI J2534 Passthru Interface Support Online Module Programming Better thanFord VCM II

FVDI J2534 is a vehicle communication interface device that full compatible with SAE J2534-1 and partly compatible with SAE J2534-2.It supports most of vehicle communication protocols and can be used as J2534 PassThru device for many dealer level diagnostic software.And it can be used as a ELM327 device also,support most of ELM327 software.

FVDI J2534 Support Softwares:

Ford IDS V116
Mazda IDS V116
Toyota Techstream V13.00
Land Rover/Jaguar SDD2 V154
Nissan Consult II Plus R2R V80.11

ELMconfig
Forscan
FOCCCUS

FVDI J2534 Comparison Table with others IDS diagnostic Interface

FVDI J2534 VS. Toyota TIS:

FVDI J2534 Support Protocols:

ISO9141 IS014230
J1850 VPW
J1850 PWM(Ford SCP)
IS011898 HS(500K BPS)
IS011898 MS(125K BPS)
IS015765 HS(500K BPS)
IS015765 MS(125K BPS)
FEPS(Flash EEPROM Program Signal)
KWP1281
J2819(TP2.0)

What’s in FVDI J2534 Package ?

Elm327 Usb software, free download

STIC FVDI J2534 Interface

Elm327 Ford Software

USB Data Cable

Software DVD